Sweep & inspection
Caps & crowns
Flue relining
Masonry repair
Gas fireplace serviceLevel 1 sweep and inspection to the NFPA 211 annual standard - flue, crown, cap, and flashing checked and photographed
Chimney sweep logs do not sweep chimneys. They loosen some creosote - which then falls where a brush and vacuum still have to collect it.
Trusted Chimney Cap & Crown for Preston Hollow Homeowners
Water is what ends most chimneys in Preston Hollow, and it almost always gets in at the top. A missing or loose cap lets rain run straight down the flue, and a cracked crown lets it soak into the masonry around it. Both problems start small and stay invisible until the damage is expensive. Our technicians have up to 9 years of experience reading exactly that kind of wear, and our cap and crown work relies on Gelco and Famco components chosen for the job rather than whatever is closest to hand. Call (833) 769-0219 and we’ll get a free estimate on the schedule. We answer 24/7. Fast dispatch, 7am-7pm.
What Our Chimney Cap & Crown Service Includes
Your chimney is a system – cap, crown, liner, firebox – and the top two pieces are the ones that decide how long the rest of it lasts. Here is what each part of the job covers.
Cap Installation
A chimney cap is the lid over the flue: a metal top on a mesh or louvered body that keeps rain, birds, squirrels and leaves out of the chimney while letting smoke escape. You need one on any flue that’s open to the sky, and most Preston Hollow homes with a masonry fireplace have at least one flue that either never had a cap or lost it years ago. We size a stainless or galvanized cap to the actual flue dimensions and anchor it to the crown so wind doesn’t walk it loose.

Cap Replacement
Caps fail in slow, predictable ways: rust-through on the body, a top plate that dents and ponds water, mesh that tears where birds have worked at it, or legs that pull free of the flue after years of expansion and contraction. A cap that’s loose or holed is worse than no cap in some ways, because it directs water onto the crown instead of shedding it. We pull the old unit, check the flue tile and crown underneath for damage it may have been hiding, and fit a replacement that matches the flue.

Crown Repair
The crown is the concrete or mortar slab at the very top of the chimney that slopes away from the flue and sends water off the sides. Hairline cracks are normal as it cures, but cracks wider than a hairline let water into the masonry below, and that’s where spalling brick, rusted dampers and interior staining begin. We repair crowns that are cracked but structurally sound, and rebuild those that have come apart, working the slope back to where it sheds properly.

Crown Coating
A crown coating is a flexible, weather-resistant membrane applied over a sound crown to seal the small cracks a rigid slab will always develop. It’s the right call when the crown is intact but showing surface checking, or when you want to protect a freshly repaired crown from the next decade of sun and rain. We prep the surface properly first, because a coating over dirt or loose mortar won’t hold. Gelco crown material is what we reach for on these jobs.
Multi-Flue Cap
A multi-flue cap covers two or more flues under one housing, which is common on the larger Preston Hollow homes where a fireplace and a furnace or second fireplace share the chimney stack. It gives you one clean, level lid instead of a cluster of separate caps at different heights, and it protects the whole crown from above. We measure every flue opening and build the housing so each flue still draws the way it should.
Custom Cap
Odd flue sizes, unusual stack shapes, oval clay tiles, and chimneys with a decorative shroud all call for a cap built to the opening rather than a stock size forced to fit. A custom cap is worth it when a standard unit would leave gaps or need to be screwed down through the flue tile. We take the measurements on site and have the cap fabricated in copper or stainless to match.
Styles & brands we work with
- Sweep & inspection
- Caps & crowns
- Flue relining
- Masonry repair
- Gas fireplace service
Brands We Service for Chimney Cap & Crown
We work with a short list of professional-grade brands because we’ve seen how each one holds up on real chimneys. DuraFlex flexible liner systems are what we install when a reline is needed alongside cap work, and we know how their components fit together at the top of the flue. Gelco crown material is our choice for crown repair and coating, since it’s formulated to flex with the masonry instead of cracking away from it. Olympia Chimney caps come up often on multi-flue jobs where the housing has to be sized precisely.
We also fit Famco caps and crown components, particularly on custom and multi-flue work where the fit matters more than the catalog number. HeatShield isn’t a cap product, but it’s the system we use when crown water damage has reached the flue liner and resurfacing makes more sense than a full reline. Whether your chimney carries Gelco, Famco, Olympia Chimney or any other make, we can help.
Signs You Need Chimney Cap & Crown Right Now
- Water in the firebox after rain. If you find damp ash, rust stains or a puddle on the damper after a storm, the cap or crown is letting water in. That moisture reaches the damper, the smoke shelf and the firebox floor, and rust there means the metal is already thinning.
- Cracks in the crown wider than a hairline. A visible crack that catches a fingernail is a path for water into the brick below. Left alone, it shows up later as flaking brick faces and white mineral staining on the chimney’s exterior.
- Rust on the cap or its mesh. Rusted-through mesh and a sagging top plate mean the cap is at the end of its life. A cap in that condition can drop debris into the flue and no longer keeps animals out.
- Birds, squirrels or leaves in the chimney. Nesting material blocks the flue and is a fire hazard, and it usually means the cap is missing or the mesh is torn. This one is worth fixing before the season turns, not after.
- Crumbling mortar at the top of the stack. Loose mortar joints just under the crown signal that water has been working its way in for a while. Repairing the crown and the top courses together costs far less than rebuilding the upper stack later.
Our Chimney Cap & Crown Process – Step by Step
- 1
We look before we quote. Every cap and crown job starts with a look at the top of the chimney, either from the roof or with a camera, so we can see the flue tile, the crown surface and the cap anchors together. We check the firebox and damper from below too, because water damage shows there first. You get a written estimate before anything gets ordered.
- 2
We photograph what we find. You see the same images we do: the crack, the rusted mesh, the gap where the cap pulled loose. Nothing gets recommended that isn’t visible in those photos, and if part of the chimney is fine, we say so and leave it alone.
- 3
We prep the surface properly. Crown repair and coating only last if the old surface is cleaned, the loose material cut back and the cracks chased out. On cap jobs we check the flue tile edge for chips, since a cap sits on that edge and a broken tile means the cap won’t seat flat.
- 4
We install to the flue, not to the nearest stock size. Caps get anchored into the crown with the right fasteners and sealed at the joint. Crown work gets formed or coated with the slope restored so water runs off the sides. Gelco and Famco components are part of how we get that fit.
- 5
We walk you through the finished work. Before we leave, we show you the completed cap or crown and explain what to watch for over the next few seasons. If the inspection turned up something else – a liner issue, a damper that needs attention – you’ll hear about it plainly, with the photos to back it up, and you decide what happens next.
See the difference
Before
After
Before
After
Before
AfterHow Much Does Chimney Cap & Crown Cost in Preston Hollow?
A typical single-flue cap installation in Preston Hollow runs $250 – $550 depending on the flue size and whether you choose galvanized or stainless. Cap replacement lands in a similar range, since removing the old unit and checking the crown underneath is part of the job. Crown repair generally runs $400 – $900 for cracked but sound crowns, while a crown rebuild where the slab has come apart runs $900 – $2,000 or more depending on the size of the chimney and how much of the top needs to come down. Crown coating sits at the lower end, around $350 – $700.
What moves the price: the number of flues, the height and pitch of the roof, whether the chimney has a decorative shroud, and how much of the crown actually needs to be cut out versus sealed. Multi-flue and custom caps cost more than a single stock unit because they’re measured and built for your stack. The way to avoid overpaying isn’t to chase the lowest bid – it’s to make sure the quote covers the crown inspection and the seal at the cap joint, because a cheap cap that leaks at the base costs more in the long run. Our estimate is free, it’s written, and it sets the final price. Nothing is recommended without camera evidence you can see for yourself, and if the work can safely wait until next season, we’ll tell you that too.
Chimney Cap & Crown Near Preston Hollow – Our Service Area
We serve homeowners across Preston Hollow and the surrounding neighborhoods, including Bluffview, University Park, Highland Park, Forest Hills, Lake Highlands, Prestonwood, Lochwood, Kessler Park, East Dallas, Farmers Branch and Addison. Roofs and stacks vary block to block, so we measure on site rather than quoting from a photo. If you’re comparing options for chimney sweep in Preston Hollow work alongside your cap and crown job, that’s a conversation we’re glad to have. For a closer look at cap and crown work in nearby areas, see our chimney cap & crown page for Prestonwood and our chimney cap & crown page for East Dallas.
Serving Preston Hollow, TX – Our Local Coverage Area
We serve Preston Hollow and nearby communities. Use the map below to see the area we cover. If you’re nearby, we can almost certainly help.
Frequently Asked Questions – Chimney Cap & Crown in Preston Hollow
It’s the repair and installation of the two pieces at the very top of your chimney: the cap, which is the metal lid over the flue, and the crown, which is the concrete or mortar slab that slopes water away from the stack. Together they’re the chimney’s first line of defense against rain, and they’re the most common source of water intrusion we find. We install, replace and repair both, and we check the flue tile underneath while we’re up there.
A single cap installation usually takes a couple of hours, and a cap replacement runs about the same. Crown repair takes longer, often most of a day, because the surface has to be prepped and the material needs time to set properly. A full crown rebuild or a custom cap that has to be fabricated will take longer, and we’ll give you the timeline in the written estimate.
A typical cap installation runs $250 – $550, crown repair $400 – $900, and a full crown rebuild $900 – $2,000 or more depending on the size of the stack. Multi-flue and custom caps cost more because they’re built to measure. The estimate is free and the written quote sets the final price. Call (833) 769-0219 for an exact quote – estimates are free.
Yes. We fit Gelco crown material, Famco caps and crown components, and Olympia Chimney caps regularly, and we know how each one is meant to sit on the flue. If your chimney already has one of these brands, we can match or replace it. Whether it’s Gelco, Famco, Olympia Chimney or any other make, we can help.
Same-day service is often possible when the schedule allows, and we’ll tell you honestly what’s available when you call. We answer 24/7. Fast dispatch from 7am to 7pm, Sunday through Friday. A call outside dispatch hours is booked into the next opening. We’re closed Saturday.
We stand behind the workmanship on every cap and crown job, and the materials carry the manufacturer’s warranty from Gelco, Famco and the other brands we use. We’ll explain what’s covered in plain terms when we give you the estimate, so there are no surprises later. If something isn’t right after the job, call us and we’ll come back out to look at it.
Clear access to the fireplace and the chimney exterior, and make sure someone is home to let us in. If you have pets, keep them away from the work area. That’s really all it takes – we bring the tools, the materials and the camera, and we handle the rest. Call (833) 769-0219 to get on the schedule.
Schedule Your Chimney Cap & Crown Service in Preston Hollow Today
A sound cap and crown is the least expensive protection your chimney will ever get, and it’s the repair that prevents the costly ones. Call (833) 769-0219 for a free, no-obligation estimate on cap installation, crown repair or a full rebuild. We answer 24/7. Fast dispatch from 7am to 7pm, Sunday through Friday. We’ll show you what we find, quote it in writing, and let you decide.
Written by the team at Chimney Sweep Preston Hollow.